KL1000 Classic - 2014 Vertical Installation Instructions 04/14 >

KL1000 Classic - 2014 Vertical Installation Instructions 04/14 >

Fitting Instructions 

The Cabinet Lock can be fitted to:

  • Cupboards, cabinets and lockers etc as a direct replacement for existing cam locks.

  • It can also be easily fitted to cupboards and cabinets that do not have an existing locking device.

kl1000 install

 

Special Notes

  • Before installing the lock, load the batteries and familiarise yourself with the operation and programming.

  • The handle will not turn until you enter the factory default Master Code: 11 33 55 77 OR the User Code 22 44.

  • Please see Vertical 2014  – Vertical 04/14 programming guide to set your own codes.

  • Your KitLock is supplied ready to fit to doors up to 19mm (3⁄4”) thick. For doors between 19mm (3⁄4”) and 25mm (1”) thick, you will need to install the 28.5mm (1 1⁄8”) spare spindle (see below). A 12mm (1⁄2”) spindle is also included for sheet metal doors (see below).

    KL1000 installation2

 

Installation Guide

  • Replacing existing cam lock with the Cabinet Lock

    1. Remove existing cam lock.

    2. Place 16mm (5⁄8″) template hole over the hole left by cam lock and mark upper fixing hole.

    3. Drill the 6mm (1⁄4″) upper fixing hole.

    4. Fit the KitLock to the door by passing the spindle through the 16mm (5⁄6″) hole.

    5. If required, from the inside of the door, pass either of the packing piece over the spindle to centralise the lock.

    6. Now secure the lock by threading the large nut onto the spindle.

    7. Fit one of the upper fixing bolts to suit your door thickness.

    8. Tighten the lower fixing nut and upper bolt.

    9. Select the cam which suits your door and frame and attach it to the square shaft at the end of the spindle.

    10. Now chech the operation of the lock using the factory User Code 22 44.

    11. If the lock is functioning correctly, CHANGE THE DEFAULT MASTER CODE 11 33 55 77 and DEFAULT USER CODE 22 44 and program the lock using the programming and operating instructions.

  • New Installation

    1. Place template on door and mark upper 6mm (1⁄4″) hole and lower 16mm (5⁄8″) hole.

      • IMPORTANT NOTE: Before drilling fixing holes, please ensure that the position of the cabinet lock when fitted will allow enough clearance for selected cam to work.

    2. Drill both fixing holes.

    3. Continue installation from step 4 to 11 above.

 

  © 2019 Codelocks Ltd.  All rights reserved.

 

    • Related Articles

    • KitLock Slam Latch - Installation Instructions

      Suitable for use with the KitLock KL1000 family: KL1000 Classic, KL1000 Classic+, KL1000 G3, KL1000 G3 NetCode, KL1000 NetCode, KL1000 RFID. SPECIAL NOTE The maximum door thickness when using the Slam Latch is 20mm (3/4”). Before installation, ...
    • KL1000 Classic Premier Pas [FR]

      La KL1000 Classic est fournie avec un code maître (11335577) et un code utilisateur (2244) réglés en usine, et le mode Usage privé est activé. Dans ce mode, la serrure reste verrouillée jusqu'à ce qu'un code utilisateur valide à 4 chiffres soit ...
    • KL1000 Classic Getting Started Guide [GB]

      The KL1000 Classic is supplied with a factory set Master Code (11335577) and User Code (2244), and the Private Use Function enabled.  In this function, the lock will remain locked until a valid 4 digit User Code is entered. On entry of a valid User ...
    • KL1000 Classic Kurzanleitung [DE]

      Der KL1000 Classic wird mit einem werksseitig eingestellten Master Code (11335577), Benutzercode (2244) und aktivierter Privatnut¬zungsfunktion geliefert. Bei dieser Funktion bleibt das Schloss gesperrt, bis ein gültiger 4-stelliger Benutzercode ...
    • KL1000 Classic Komma Igång [SV]

      KL1000 Classic levereras med en fabriksinställd huvudkod (11335577) och användarkod (2244), och funktionen för privat användning är aktiverad. I denna funktion förblir låset låst tills en giltig 4-siffig användarkod har angetts. När du anger en ...