KL10 - Installation and Operating Instructions

KL10 - Installation and Operating Instructions


Special Notes

Please read carefully:
  • Before installing the lock, familiarise yourself with the installation and operating instructions.
  • The factory preset combination is 0-0-0-0.
  • Your KitLock is supplied ready to fit to doors up to 19mm (3⁄4”) thick.
 

Fitting Instructions

The KitLock can be fitted to cabinets, cupboards and lockers etc. as a direct replacement for existing cam locks.

It can also be fitted easily to cupboards and cabinets that do not have an existing locking device.

 

Fixing Pack A (Default Supply)

  • KitLock
  • Hex nut x 1
  • Straight cam x 1
  • Screw x 1

Fixing Pack B (Optional Additional Fixings)

  • Metal clip x 1
  • Screws x 2
  • Washer x 1
  • Crank cam x 1


 

Installation Guide

Replace existing cam lock with KitLock

1. Remove existing cam lock.
2. Fit the KitLock to the door, passing through the existing spindle hole.
3. Now secure the lock by threading the hex nut onto the spindle.
4. Fit cam and secure with screw.
5. Now check the operation of the lock using the factory preset combination 0-0-0-0.
6. If the lock is functioning correctly, change the code using the instructions overleaf.

New Installation

N.B. Optional Fixing Pack B (above) may be required.
1. Mark a position at a suitable distance from the door edge, ensuring enough clearance for the cam to work.
2. Using the ‘Typical Door Prep.’ Dimensions (see overleaf), drill a hole to suit.
3. Continue installations from step 2 to 6, left.

 

Changing the code

  1. With the indicator in the open position, turn the dials to the factory preset combination 0-0-0-0 Note: If you have already changed the code, use your current combination for this step.
  2. Depress the reset button fully and hold, turn the dials to your desired combination. Note: Do not let go of the reset button while setting your combination.
  3. Release the reset button after checking your combination is correct. Note: The outer casing will turn freely between the open and locked position until the combination has been scrambled.
 

How to use your lock

  1. Once you have chosen and set your combination, turn the outer casing so the indicator is in the locked position.
  2. Make a note of your chosen combination and scramble the dials. The lock is now locked.
  3. To reopen, rotate the dials to your chosen combinations and turn the outer casing so the indicator is in the open position.
Note: Your chosen combination will continue to operate the lock until it is changed.

 

Finding the code

Note: This function requires the Master Key (sold separately).
  1. Insert the master key when the indicator is in the locked position.
  2. Turn the key clockwise 90 degrees.
  3. Gently rotate each dial upwards until it stops. This is your code.
  4. Turn the master key anticlockwise 90 degrees and remove.



 

Dimensions





IOI-KL10-v1-0119
© 2019 Codelocks Ltd.  All rights reserved.

    • Related Articles

    • KitLock Slam Latch - Installation Instructions

      Suitable for use with the KitLock KL1000 family: KL1000 Classic, KL1000 Classic+, KL1000 G3, KL1000 G3 NetCode, KL1000 NetCode, KL1000 RFID. SPECIAL NOTE The maximum door thickness when using the Slam Latch is 20mm (3/4”). Before installation, ...
    • KL1100 RFID - Installation Instructions & Template

      INSTALLATION Please read carefully: Before installing the lock, read the programming and operating instructions suited to your KL1100 model. Please note, the KL1100 RFID requires a Master Card to be assigned on powering up. Instructions can be found ...
    • KL1100 KeyPad - Installation Instructions & Template

      INSTALLATION Please read carefully: Before installing the lock, read the programming and operating instructions suited to your KL1100 model. Please note, the KL1100 RFID requires a Master Card to be assigned on powering up. Instructions can be found ...
    • KL1100 RFID - Programming and Operating Instructions

      ABOUT KL1100 RFID The KL1100 RFID can operate in Standalone Mode or in Remote Card Authorisation (RCA) Mode. RCA Mode gives the ability to remotely set-up and allocate cards to locks or lock groups  with our offline or cloud based software. ...
    • KL2O - Installation and Operating Instructions

      Special Notes Please read carefully: Before installing the lock, familiarise yourself with the installation and operating instructions. The factory preset combination is 0-0-0-0. Your KitLock is supplied ready to fit to doors up to 22mm (7/8”) thick. ...