CL5000 NetCode® - Programming and Operating Instructions

CL5000 NetCode® - Do-Not-Disturb Feature

Do-Not-Disturb for the CL5000 NetCode® Lock
The CL5000 NetCode® lock can be used in conjunction with an Accessory Panel to provide Do-Not-Disturb features. Where the lock has been supplied without the Accessory Panel, a separate purchase will be required in order to use the Do-Not-Disturb feature.

Installation

To add the Accessory Panel, you will need to remove the lock from the door if already installed. Although the battery cover if supplied will no longer be required, retain the battery cover fixing bolt.
  1. Connect the ribbon cable to the multi-way connector on the PCBA in the frontplate
  2. Install the lock as per the installation instructions, remembering to pass both the power and ribbon cables through the cable tube to the backplate
  3. Connect the backplate end of the ribbon cable to the Accessory Panel
  4. Connect the sensor cable to the Accessory Panel
  5. Secure the Accessory Panel in place of the original battery cover

Programming

Each programming sequence starts with the #Master Code or #Sub-Master Code. The singular • blue dots throughout the sequence represent an acceptance flash; the keypad will illuminate blue to confirm a correct input. At the end of a sequence, the keypad will flash twice • • confirming it’s complete and programming has been successful. 

When in Programming Mode, a Program Code must be entered within 5 seconds, otherwise the Red LED will flash and beep and the lock will revert to normal. If a programming mistake is made, wait 5 seconds, the Red LED will flash and beep and the lock will revert to normal.

Do-Not-Disturb Programming

Enable Do-Not-Disturb

#(Sub)Master Code  •  18  •  1 • •
Example: #12345678  •  18 •  1 •  1 • •
Result: Do-Not-Disturb has been enabled. Pressing the lock button on the Accessory Panel will activate Do-Not-Disturb. Pressing the un-lock button will deactivate Do-Not-Disturb. When activated, only Master and Sub-Master Users will be permitted access.

Disable Do-Not-Disturb

#(Sub)Master Code  •  18  •  0 • •
Example: #12345678  •  18  •  0  • •
Result: Do-Not-Disturb has been disabled. 
Note: Unplug the ribbon cable from the Accessory Panel.

The Codelocks Control + Convenience logo and NetCode® are registered trademarks of Codelocks Ltd., registered in the United Kingdom, United States and other countries and regions.


    • Related Articles

    • NetCode Modes Explained

      Notice: The C3 Smart App replaced the K3 Connect App on February 14, 2023. For more information on how to download, set up and use C3 Smart with your Codelocks Smart Locks, visit: c3smart.net or contact Codelocks Support. Important Notes Please note ...

    • Change the NetCode Mode

      Notice: The C3 Smart App replaced the K3 Connect App on February 14, 2023. For more information on how to download, set up and use C3 Smart with your Codelocks Smart Locks, visit: c3smart.net or contact Codelocks Support. Important note: When using ...

    • How to request a NetCode via SMS

      1. For a phone number to be able to request a NetCode it will first need to be added to the whitelist.  To do this, from the Codelocks Connect portal homepage click on Manage your Locks & Access, then Whitelist. 2. Click on Add New and when prompted, ...

    • How to request a NetCode via SMS

      Notice: The C3 Smart App replaced the K3 Connect App on February 14, 2023. For more information on how to download, set up and use C3 Smart with your Codelocks Smart Locks, visit: c3smart.net or contact Codelocks Support. 1. For a phone number to be ...

    • KL1000 NetCode - Switching NetCode Modes

      On the KL1000 NetCode there are a few different NetCode modes available to choose from. This article will explain how to switch in-between them and provide an explanation of each modes features.   Change Mode Sequences To turn on a mode you will need ...