This range of locks can be operated and managed directly via the keypad or via a compatible smartphone by downloading the K3 Connect App. This Getting Started guide contains the common functions to enable you to quickly program your lock.
For detailed instructions, refer to the Programming & Operating Instructions.
Master Code
The factory set Master Code is #12345678. This should be changed immediately after installation (Program 01). The Master Code (and Sub-Master Code if set) always start with the # button. This puts the lock in Programming Mode.
Access Methods
The lock supports a maximum of 350 Clients (users): User Codes (100), User Cards (150) and User Compatible Phones (100).
Keypad
The lock has a 12 button, back-lit keypad which includes * and # buttons. The # button is only used for programming. The * button is used in some Programs and with NetCodes.
Code Free
Code Free can be configured via Program 04 (refer to the Programming & Operating Instructions) or via Key-in-Lever by changing the cylinder tailpiece (refer to Installation Instructions).
Remote Release
The lock has two sets of terminals within the front housing for remote release, labelled REM1 and REM2. REM1 is intended for push-button release where the lock will open for the normal set time. REM2 is intended for use where the lock needs to be released for a longer period. When a switch or relay connected to REM2 is closed, the lock will open for a period of 30 minutes after which the lock will revert to normal operation.
Refer to Installation Instructions for further information.
Manage with the K3 Connect App
The lock can be managed with the K3 Connect App by any Bluetooth compatible smartphone.
The App is available on:
Apple App Store for Apple devices or Google Play™ for Android™ devices by searching for K3 Connect.
For detailed instructions, refer to the Programming & Operating Instructions.
The lock can be reset to its original factory settings. You may need to do this if the Master Code is no longer known or you no longer have management access via a smartphone. To reset the lock, you must have access to the battery compartment in the rear of the lock.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Android, Google Play and the Google Play logo are trademarks of Google Inc.
01 Change the Master Code
Note: The Master Code is 8 digits in length
#Master Code • 01 • New Master Code • New Master Code ••
Example: #12345678 • 01 • 87654321 • 87654321 ••
Result: The Master Code has been changed to 87654321
02 Change the Sub-Master Code
Note: The Sub-Master Code is 8 digits in length
#Master Code • 02 • New Sub-Master Code • New Sub-Master Code ••
Example: #12345678 • 02 • 44556677 • 44556677 ••
Result: The Sub-Master Code has been changed to 44556677
03 Delete the Sub-Master Code
#Master Code • 03 ••
Example: #12345678 • 03 ••
Result: The Sub-Master Code has been deleted
15.1 Lock-Down
Prevent the lock from being unlocked by any method except via Master Code and Sub-Master Code:
#Master Code • 15 • 1 ••
Example: #12345678 • 15 • 1 ••
Result: Lock-Down is enabled. Only the Master and Sub-Master Codes can be used to open the lock.
15.2 Cancel Lock-Down
#Master Code • 15 • 2 ••
Example: #12345678 • 15 • 2 ••
Result: Lock-Down is cancelled.
20.1 Add a Code Client
#Master Code • 20 • 1 • Code ••
Example: #12345678 • 20 • 1 • 3366 ••
Result: The Code 3366 can now be used to unlock the lock.
20.2 Add a One-Time Code Client
#Master Code • 20 • 2 • Code ••
Example: #12345678 • 20 • 2 • 7788 ••
Result: The Code 7788 can be used to unlock the lock once only.
20.3 Add a Smart Card Client
Note: After entering the program below, the lock will wait for a MIFARE based smart card to be placed over the keypad.
#Master Code • 20 • 3 •• present MIFARE card
Example: #12345678 • 20 • 3 •• present MIFARE card
Result: The smart card will be able to unlock the lock.
Note: Up to 150 cards can be registered.
21 Suspend a Code Client
#Master Code • 21 • Code ••
Example: #12345678 • 21 • 1199 ••
Result: The Code 1199 has been suspended.
22 Restore a Code Client
#Master Code • 22 • Code ••
Example: #12345678 • 22 • 1199 ••
Result: The Code 1199 has been restored.
Incorrect Code/Card
If 3 incorrect access attempts are made, the lock will suspend activity for 30 seconds.
Programming Error
If a programming mistake is made, the keypad will flash red and the lock will revert to normal operation.
Battery Failure
If the battery fails, the key-override should be used to open the lock. Batteries can be replaced by opening the battery cover on the rear of the lock. Always use high-quality AA batteries and ensure that the batteries are inserted correctly. Please refer to local authority recommendations for the disposal of old batteries.
GS-CL4500-v1:1016
© 2019 Codelocks Ltd. All rights reserved.