A3 DUAL - Getting Started Guide Published
ABOUT
The A3 Dual Standalone Keypad Door Controller with RFID is a compact, standalone programmable access control system that provides proximity access for up to 600 users.
SPECIFICATIONS
Advanced Features
ADV Guides, programming instructions and wiring diagrams for the A3 Dual advanced features can be found at: www.codelockssupport.com
Clients
Compatible With 13.56MHz MIFARE® (ISO14443 Type A) & 125KHz
Client IDs 598 Standard Clients: (Code and/or Card)
2 Panic Clients
Operation
Voltage 12-18V DC
Idle Current 35mA
Working Current 100mA
Max. Output Load 2A
Relay Output Time 1-99s (5s default)
Inputs/Outputs Relay, Push-to-Exit, Alarm, Door Contact, Wiegand Input, Wiegand Output
Weigard ADV Input/Output: 26-37 bits
PIN Output: 4 bits, 8 bits (ASCII), 10 Digits Virtual Number (4 bits default)
Read Range 60mm (2 3/8”)
Environment Rating IP66
Temperature -40°C ~ 60°C (-40°F ~ 140°F)
Humidity 0%RH ~ 98%RH
INSTALLATION
BOX CONTENTS
| Description | Quantity |
| A3 Dual Standalone Door Controller | 1 |
Master Programming Cards Master Add Card (1) Master Delete Card (1) | 2 |
| Allen Key | 1 |
| Self-Tapping Screws | 2 |
| Wall Plugs | 2 |
| 1N4004 Diode | 1 |
INSTALL
1. Remove back cover from the unit by removing the bottom screw
2. Drill two fixing holes1 and a cable passage hole
3. Fix back cover to wall
4. Thread cable through back cover into cable passage hole
5. Reattach unit to the back cover
(1) The unit may also be flush mounted.
(2) Use appropriate fixings for your application. Wall plugs supplied may not be suitable for all applications.
WIRING
| Colour | Function | Notes |
| Red | Power+ | 12-18V DC Regulated Power Supply |
| Black | GND | Ground |
| Blue | NO | Normally Open Relay Output |
| Purple | COM | Common Connection for Relay Output |
| Orange | NC | Normally Closed Relay Output |
| Yellow | OPEN | Request to Exit |
Wiegand Wiring (Wiegand Reader or Controller) ADV
| Colour | Function | Notes |
| Green | D0 | Wiegand Input/Output Data 0 |
| White | D1 | Wiegand Input/Output Data 1 |
Advanced I/O Features ADV
| Colour | Function | Notes |
| Grey | Alarm Output | Negative Contact for Alarm |
| Brown | Door Contact | Door Contact Input (NC) |
WIRING DIAGRAMS
Note: Install a 1N4004 or equivalent diode when using a common power supply.
OPERATING INSTRUCTIONS
When first powered, the unit will be in Standalone/Controller Mode; the unit acts as both controller and reader, and will allow both Card Clients and Code Clients to be programmed. The pre-registered Master Programming Cards can be used to quickly add (and delete) new Card Clients. For further programming, the keypad can be used.
ADV Additional access modes are available.
GENERAL OPERATION
| Unlock/Open Door | Present a valid Card Client to the unit or enter a valid Code Client followed by a # Example: 5 7 4 2 # The LED will turn green and a single beep will sound to indicate acceptance |
| Silence Alarm | Present a valid Code or Card Client, or enter the Master Code to silence the alarm |
| Exit Programming Mode | To exit Programming Mode at any time, press the * button until you see a solid red light |
CHANGE THE MASTER CODE
Note: The Master Code is 6 digits in length. Default set Master Code is 123456.| Enter Programming Mode | * Master Code # |
| Enter New Master Code | 0 New Master Code # New Master Code # |
| Exit Programming Mode | * |
ADD CARD CLIENTS
New Card Clients can be added via the infrared Remote Control Programmer or using the Master Add Card.
| Enter Programming Mode | * Master Code # |
| Add a Card Client Unit will assign the Card Client to the next available ID. | 1 Present Card Multiple Card Clients may be added by presenting them consecutively before exiting Programming Mode. |
| OR | |
Add a Card Client to Specific ID Unit will assign the Card Client to the specified ID (1-598). | 1 Specific Client ID # Present Card |
| Exit Programming Mode | * |
The Master Add Card can be used to add new Card Clients directly, without using the keypad. Using this method, the new Card Client will be assigned to the next available ID.
Add a Card Client via Master Add Card | 1. Present Master Add Card 2. Present new Card Client (repeat as required) 3. Present Master Add Card to end |
ADD CODE CLIENTS
New Code Clients can be added via the keypad.
Note: Code Clients may be 4-6 digits long. The code 8 8 8 8 is reserved and cannot be used.
| Enter Programming Mode | * Master Code # |
| Add a Code Client The Code Client will be assigned to the next available ID. Multiple Code Clients may be added sequentially. | Single Client 1 Present Card Multiple Clients 1 Enter New Code # Enter New Code # Enter New Code # (repeat as required) |
| OR | |
Add a Card Client to Specific ID Card Client to the specified ID (1-598) | 1 Specific Client ID (1-598 # Enter New Code # |
| Exit Programming Mode | * |
ADD PANIC CLIENTS
A Panic Client allows access and will trigger an alarm if connected.
| Enter Programming Mode | * Master Code # |
| Add a Panic Card | 1 Client ID (599 or 600) # Present Card |
| OR | |
Add a Panic Code | 1 Client ID (599 or 600) # Enter New Code # |
| Exit Programming Mode | * |
2 Specific Client ID #
OR
Delete all Clients
DELETE CARD CLIENTS
Existing Card Clients can be deleted via the keypad, or using the Master Delete Card.
| Enter Programming Mode | * Master Code # |
Delete a Card Client Presented Card Client will be deleted. Multiple Card Clients may be deleted sequentially. | 2 Present Card Multiple Clients 2 Present Card - Present Card - Present Card (repeat as required) |
| OR | |
Delete a Card Client to Specific ID Unit will delete the Card Client at the specified ID (1-598). | |
OR | |
Delete all Clients Unit will delete all Card and Code Clients. | 2 Master Code # |
| Exit Programming Mode | * |
MIFARE® is a registered trademark of NXP B.V. and is used under license.
GSG-AL03DX-v1-0819
© 2019 Codelocks Ltd. All rights reserved.